I love flowers of all kinds, and succulents are included in the list of plants I enjoy. Sometimes, however, a real plant isn’t convenient. So, this repurposed soda can flower planter is ideal for those of us who want the look of flowers but no pressure to care for them day to day. A unique fake planter is made from an upcycled and painted empty soda can. It’s ideal for showing off fake flowers, but can be used for small amounts of real flowers! Whether you are looking to add a splash of color to your home or your office, this is sure to be a perfect way to do it!
Soda Can Flower Planter
Do you like plants but don’t have the time to take care of them? This is the perfect product for you! The soda can flower planter is a beautiful way to add some life to your home or office. You can use it to hold fake or real plants, and it’s made out of an upcycled soda can so it’s environmentally friendly.
It’s easy to customize with your favorite colors and can be used for real or fake flowers or plants of many kinds. I love this for these cute little succulents but can definitely see making a few of these with flowers of different colors and styles to line along the mantle or even on a shelf in my office. And since it’s easy to take care of, you’ll be able to enjoy your plants without worrying about them dying.
If you have a lot of soda cans and want something different to use them for instead of just recycling, check out this huge list of DIY ways to recycle soda cans into something unique!
What Size Can Should I Use?
The best part about this project is that you are making something beautiful with something upcycled. But, the next best thing about this project is that there are no set rules. I love that you can use whatever size can that you have on hand. Depending on what you can use, you might need to adjust what you place inside of the can to make sure it fits properly.
For this taller planter, a 20-ounce to 24-ounce can is perfect. You can, of course, use a 12-ounce can, or even an 8-ounce can for a tiny planter. Just use what you have on hand to make this planter. There is no need to go out and buy something new or different than what you have on hand.
How Can I Make Sure There are No Sharp Edges?
If you are using a can that has been used before, make sure to clean it out completely and let it dry. Rinsing out any residual soda or alcohol from the can is a must so it doesn’t start smelling.
Once the can is clean, you’ll follow directions to cut out the side to create the planter. To get rid of the sharp edges on that area, use a bit of sandpaper or simply go back over it with a knife to trim off anything jagged.
What Paint is Best for an Aluminum Soda Can?
I alternate between acrylic craft paints and spray paint when working with soda cans. Both offer good coverage and are typically affordable. In this instance, the detailed red dots require something more exact. So, craft paint was the best choice for this planter.
If for some reason your can doesn’t seem to let the paint stick well, you may want to brush a piece of sandpaper over the edges to roughen the exterior a bit. Not a lot, but just enough to add texture for the paint to cling to.
Can I Use This For Live Flowers?
Absolutely! What you add to the planter will depend upon the size can you use. However, it is great for both real and fake flowers and plants. I prefer the maintenance-free look sometimes when life is busy and I know I won’t always be there to care for my flowers.
If you choose to put a real plant into the can, poke a few holes in the bottom for drainage. Add a layer of soil, then the flowers. When displaying this, I would add a small tray beneath the planters to catch any excess liquid from watering the plants.
- Soda can
- White paper
- White craft paint
- Red craft paint
- Fake succulent plants
- Black marker
- Hot glue gun
- Hot glue sticks
How to Make a Soda Can Flower Planter
Rinse out your soda can and let it air dry before you begin making your planter. Then, fold a piece of white paper in half, and lay the soda can on the table right beside it. Use the soda can as a guide to mark the paper about 1″ from both the top and the bottom of the can.
Now, use a marker or pen to connect the sides you just marked creating an arch on the paper.
Cut out this arch and unfold it.
Now, you will place it against the can, and use it to trace around the can where you want to cut. This is going to create the open space of the can for planting your succulents.
Carefully cut out the can side using scissors or a craft knife and smooth the edges.
Now, you get to paint the can. Cover the entire outside of the can with white paint then set it aside to dry. Give it at least 30-minutes, but make sure it is no longer tacky before you paint anything further.
Once the can is dry, use a paintbrush to coat the top and bottom of the can with red paint. You want to cover the tab and all of the top of the can as well as the bottom edge. You do not have to paint the actual bottom of the can.
Let this dry if desired, then use a round brush or the end of a pencil eraser, to dot red polka dots all over the can. Put them randomly around the can until you are satisfied with the look.
Next, use the same brush or eraser to add dots all around the very edge of the opening of the planter.
Set the can aside to dry for another 30-minutes or more. When the paint on the soda can is completely dry, then you can use hot glue to place your selection of fake succulents on the inside bottom of the can. Continue adding until you are happy with the look.
You can make just this one, or make multiples in different colors and designs to hold succulents, flowers, or even use for a real herb garden.
More Easy Planter Ideas
I love both real and fake flowers, and that means I like a variety of options on hand. If you want more inspiration, check out some of the fun ideas below that are ideal for a variety of different flowers, both real and fake. Make sure you take a moment to bookmark these ideas, print out the tutorials, or just pin them to Pinterest to make soon.
- Decorative Clothespin Tin Can Planter
- Genius DIY Paper Straw Floating Succulent Planter
- How to Make a Decorative Lightbulb Planter
- 32 Ingenius DIY Planters for Small Places
- On a folded white piece of paper, lay the soda can and use it as a guide to mark about 1" from the top and 1" from the bottom onto the paper.
- Use a marker or pen to trace an oval shape onto the paper connecting the dots.
- Then cut out the paper.
- Place the paper against the can, and use it as a guide to trace the outline onto the can.
- Cut the center of the can out around that traced space.
- Paint the can white and set it aside to dry.
- Once the can has dried, use the red paint to paint the top tab end of the can.
- Then paint around the edge of the bottom of the can.
- Use something round (the end of a pencil) to add dots of red paint all around the can randomly.
- Then, use the same thing to add dots of paint around the edge of the opening.
- Once the paint has dried completely, begin gluing pieces of the fake succulents onto the bottom of the can.
This can be made with any sized aluminum can.
As an Amazon Associate and member of other affiliate programs, I earn from qualifying purchases.
Recycled Soda Can Butterfly Magnets | Etsy
Soda Can Airplane Sopwith Camel DIGITAL PLANS | Etsy
CUSTOM Cowboy Beer or Soda Can Hat Made to Order | Etsy
Dr Pepper Rose Necklace. Recycled Soda Can Art. Dr Pepper. | Etsy
Aluminum Soda Can Sheets/blanks set of 5 | Etsy
Orange Fanta Soy Candle Hand Poured Soda Can Candle Custom | Etsy
Finished Project Gallery
If using for real plants, punch a few holes in the bottom for water to drain.